Articles | Volume 23, issue 9
https://doi.org/10.5194/hess-23-3593-2019
https://doi.org/10.5194/hess-23-3593-2019
Research article
 | 
04 Sep 2019
Research article |  | 04 Sep 2019

A soil non-aqueous phase liquid (NAPL) flushing laboratory experiment based on measuring the dielectric properties of soil–organic mixtures via time domain reflectometry (TDR)

Alessandro Comegna, Antonio Coppola, Giovanna Dragonetti, and Angelo Sommella
Abstract

The term non-aqueous phase liquid (NAPL) refers to a group of organic compounds with scarce solubility in water. They are the products of various human activities and may be accidentally introduced into the soil system. Given their toxicity level and high mobility, NAPLs constitute a serious geo-environmental problem. Contaminant distribution in the soil and groundwater contains fundamental information for the remediation of polluted soil sites. The present research explored the possible employment of time domain reflectometry (TDR) to estimate pollutant removal in a silt-loam soil that was primarily contaminated with a corn oil as a light NAPL and then flushed with different washing solutions. Known mixtures of soil and NAPL were prepared in the laboratory to achieve soil specimens with varying pollution levels. The prepared soil samples were repacked into plastic cylinders and then placed in testing cells. Washing solutions were then injected upward into the contaminated sample, and both the quantity of remediated NAPL and the bulk dielectric permittivity of the soil sample were determined. The above data were also used to calibrate and validate a dielectric model (the α mixing model) which permits the volumetric NAPL content (θNAPL; m3 m−3) within the contaminated sample to be determined and quantified during the different decontamination stages. Our results demonstrate that during a decontamination process, the TDR device is NAPL-sensitive: the dielectric permittivity of the medium increases as the NAPL volume decreases. Moreover, decontamination progression can be monitored using a simple (one-parameter) mixing model.

Dates
1 Introduction

Soil and groundwater contamination with non-aqueous phase liquid (NAPL) from point or nonpoint sources is a severe problem of considerable complexity (Fitts, 2002; Fetter, 1993). The repercussions concern not only the deterioration of the soil's physical, mechanical and chemical properties but also account for a potentially severe hazard to the well-being of humans and other living species (Freeze, 2000).

Soil flushing is the technical procedure used for treating polluted soils with water, surfactants and co-solvents (such as methanol, ethanol and propanols). Surfactant-enhanced flushing was developed from the conventional pump-and-treat method. The success of this approach is related to the capacity of such chemical compounds to greatly enhance the aqueous solubility of oils (Pennell et al., 1994; Parnian and Ayatollahi, 2008).

There is high interfacial tension between NAPL and water molecules that makes water a non-efficient cleaning material in removing NAPL from the soil. Instead, surfactants and co-solvent agents can promote the enhanced removal of NAPL from the subsurface through mobilization and solubilization (Martel et al., 1998; Rinaldi and Francisca, 2006; Parnian and Ayatollahi, 2008).

Primary remediation entails the removal of the NAPL free phase by pumping. This extraction mechanism returns appreciable effects if there is a region of high NAPL saturation. After primary pumping, a considerable portion of NAPL remains constrained within the soil as capillary forces overcome viscous and buoyancy forces. This discontinuous NAPL phase is referred to as trapped residual NAPL (or NAPL residual saturation), and its remediation is referred to as secondary remediation (Parnian and Ayatollahi, 2008). Residual NAPL is a long-term source of soil and groundwater pollution (Mercer and Cohen, 1990; Troung Hong and Bettahar, 2000).

To develop powerful decontamination procedures, the characterization of polluted soils is required. Practices usually employed to characterize polluted soil sites are coring, soil sampling and the installation of monitoring wells for the collection of water samples from aquifers (Mercer and Cohen, 1990). Since the above procedures are costly, different dielectric techniques can be used to detect organic contaminants in soils. The most widely accepted geophysical technique, based on the principle of electromagnetic wave (EMW) propagation, is the ground-penetrating radar (GPR; Knight, 2001). Redman et al. (1991) described some field experiments in the application of GPR to detect NAPL plumes.

Rinaldi and Francisca (2006) used a coaxial impedance dielectric reflectometry (CIDR) technique to measure the complex dielectric permittivity in sands contaminated by a paraffin oil. Their research into the dielectric behavior of NAPL-contaminated soils during a decontamination process mainly focused on the removal efficiency of different washing solutions and on the spectral response of the contaminated medium during the various tests conducted.

Time domain reflectometry (TDR) is a further geophysical device based on electromagnetic wave (EMW) principles that can also be used for this purpose (Endres and Redman, 1993; Redman and DeRyck, 1994; Mohamed and Said, 2005; Moroizumi and Sasaki, 2006; Francisca and Montoro, 2012). Few experiments have been conducted coupling the TDR technique and NAPL. In these studies estimation of NAPLs using TDR measurements of dielectric properties relies greatly on various mixing models relating the measured dielectric permittivity to the volume fractions of the pore fluids and various soil phases such as solid, water, air and NAPLs (van Dam et al., 2005).

Some interesting results were achieved by Persson and Berndtsson (2002) whilst investigating the influence of different LNAPLs (i.e., light NAPLs) on TDR measurements in a homogeneous silica sand under saturated and unsaturated soil conditions. Measurements of both dielectric permittivity and electrical conductivity allowed a method to be developed (the two-step method) which measured the dielectric properties of the system against the amount of NAPL in soils. Comegna et al. (2016) developed a general TDR-based methodology for evaluating the correlations between the dielectric response and the NAPL content in variable saturated soils with different textures and pedological characteristics.

The purpose of this study was as follows: (i) to investigate a possible extension of TDR technology to assess the effects of NAPL removal in soils and (ii) revisit, on the basis of the acquired data and the experimental results, a dielectric model to predict, “in real time”, the volumetric amounts of NAPL (θNAPL) within the contaminated soil during the decontamination process.

2 Theoretical concepts of TDR

TDR is a geophysical technique employed to determine the dielectric permittivity of liquids and solids (Ferrè and Topp, 2002, described this method in detail). In general, the bulk dielectric permittivity is a complex term (εr*), which may be expressed as follows (Robinson et al., 2003):

(1) ε r * = ε r - j ε r ′′ + σ ω ε 0 ,

where εr is the real part of dielectric permittivity, which gives the energy stored in the dielectrics at a certain frequency and temperature, and εr′′ is the imaginary part due to relaxations. The zero-frequency conductivity σ, the angle frequency ω, the imaginary number j=-1 and the permittivity ε0 in free space contribute to defining εr*.

When the frequency of a TDR cable tester ranges between 200 MHz and 1.5 GHz, dielectric losses can be considered minimal (Heimovaara, 1994), and the bulk dielectric permittivity εb ( the real part of permittivity) of a probe of length L is determined from the propagation velocity v(=2L/t) of an electromagnetic wave along the wave guide across the investigated medium by the following expression:

(2) ε b = c v 2 ,

where c(=3×108 m s−1) is the velocity of an electromagnetic wave in vacuum (Topp et al., 1980) and t is travel time, i.e., the time required by the generated signal to go back and forth through the TDR probe of length L (m). This can be calculated as follows:

(3) t = 2 L c ε b .

The direct dependence of the signal's travel time t on soil dielectric permittivity is expressed by Eq. (3).

3 Estimating volumetric NAPL content during a decontamination process in soils

Dielectric mixing models, in their classical application, have been proposed to estimate the bulk dielectric permittivity of a multi-phase medium, that is, a combination of three or four dielectric phases, and to couple the dielectric permittivity of the medium to the dielectric permittivity of each single phase (Hilhorst, 1998). Recently, after analyzing the effects of organic contaminants on soil dielectric properties, the above models were further developed to estimate the dielectric properties of NAPL-polluted soils (Redman et al., 1991; Persson and Berndtsson, 2002; Francisca and Montoro, 2012; Comegna et al., 2013a, 2016, 2017).

Based on such models, in the present study, we analyze the possibility of predicting the correlations between the volumetric contents of NAPL (θNAPL) and the dielectric response (εb) of contaminated soil during the progression of a steady-state remediation process.

In the present research, we chose the so-called α model (Birchack et al., 1974; Knight and Endres, 1990; Roth et al., 1990):

(4) ε b = i = 1 n V i ε i α 1 / α ,

where Vi is the volume and εi is the permittivity of each component of the complex medium; the exponent α is a fitting parameter (α varies between −1 and 1), which may be related to the internal structure of the investigated medium (Hilhorst, 1998; Coppola et al., 2013, 2015). Under the following hypothesis, (i) the soil is homogeneous from a textural point of view, and (ii) when the soil porosity (ϕ) is constant, Eq. (4) was reformulated for our purposes.

For mixtures of soil (s) saturated with a certain amount of washing solution (ws), in rearranging the model formulation of Rinaldi and Francisca (2006), the α model yields the following:

(5) ε s - ws α = ( 1 - ϕ ) ε s α + ϕ ε ws α ,

where εs-ws is the soil-washing solution permittivity, and εs and εws are the permittivities of soil particles and washing solutions, respectively. By the same token, for soil organic (s-NAPL) compounds at saturation, the α model can be expressed as follows:

(6) ε s - NAPL α = ( 1 - ϕ ) ε s α + ϕ ε NAPL α ,

where εs-NAPL is the permittivity of the soil–NAPL mixture, and εNAPL is the oil permittivity.

A medium consisting of soil particles, washing solution and NAPL (s-ws-NAPL) can be viewed as a mix of soil-washing solution (Eq. 5) and soil–NAPL (Eq. 6):

(7) ε s - ws - NAPL α = β ε s - NAPL α + ( 1 - β ) ε s - ws α ,

where β is the relative volume of NAPL contained in the whole fluid phase,

(8) β = θ NAPL θ ws + θ NAPL = θ NAPL θ f ,

where θf is the volumetric fluid content (m3 m−3), the sum of the volumetric washing solution content (θws) and volumetric NAPL content (θNAPL); β varies between 0 (i.e., a soil-washing solution mixture) and 1 (i.e., a soil–NAPL mixture).

To estimate θNAPL, Eq. (7) is first reformulated in terms of β:

(9) β = ε s - ws α - ε s - ws - NAPL α ε s - ws α - ε s - NAPL α = ( 1 - ϕ ) ε s α + ϕ ε ws α - ε s - ws - NAPL α ( 1 - ϕ ) ε s α + ϕ ε ws α - ( 1 - ϕ ) ε s α + ϕ ε NAPL α .

Substituting Eq. (8) into Eq. (9), and considering that for a saturated medium, the volumetric fluid content is equal to soil porosity (i.e., θf=ϕ), θNAPL can be calculated as follows:

(10) θ NAPL = ( 1 - ϕ ) ε s α + ϕ ε ws α - ε s - ws - NAPL α ε ws α - ε NAPL α .

Equation (10) correlates the dependence of volumetric NAPL content with soil porosity; θNAPL can be estimated (within the contaminated soil) during the progression of a remediation process once the dielectric permittivity of the soil-contaminated mixture (εs-ws-NAPL) is known.

4 Materials and methods

4.1 Soil and fluid properties

A silt-loam anthrosol (IUSS Working Group WRB, 2006) from the region of Puglia (Italy) was used for this study. The soil texture was measured by means of the hydrometer method (Day, 1965), while the Walkley–Black procedure (Allison, 1965) was used to determine soil organic C content. The method developed by Miller and Curtis (2006) was used to measure soil electrical conductivity (ECw), while soil pH was determined on the basis of a 1:1 soil-to-water ratio (Eckert, 1988). In textural terms, the soil comprised 15.7 % sand, 11.6 % clay and 72.4 % silt. Soil porosity was 0.57 %, organic content was 1.84 %, ECw was 0.17 dS m−1 and soil pH was 8.40.

The NAPL employed for the laboratory tests was corn oil (εNAPL=3.2; ECNAPL=0.055 dS m−1 at 25 C) with a density of 0.905 g cm−3 (at 25 C). Three different removal solutions were employed for soil cleaning: (a) a first solution (referred to below as wd) composed of 99 % distilled water and 1 % commercial detergent (εd=9.22, at 25 C); (b) a second solution (wda no. 1) composed of 90 % distilled water, 1 % commercial detergent and 9 % methanol as co-solvent (εalcohol=26.13, at 25 C); and (c) a third solution (wda no. 2) composed of distilled water (85 %) with commercial detergent (1 %) and methanol (14 %). The dielectric permittivity of the washing solutions, measured at 25 C, was εwd=75.04, εwdano.1=68.98 and εwdano.2=65.92, whereas the dielectric permittivity of the tested soil saturated with each of the three cleaning solutions was εsoil+wd=34.59, εsoil+wdano.1=31.04 and εsoil+wdano.2=30.10.

https://www.hydrol-earth-syst-sci.net/23/3593/2019/hess-23-3593-2019-f01

Figure 1Experimental setup used in the NAPL removal experiments (from Comegna et al., 2013c).

Download

4.2 Measurement of dielectric permittivity of soil–NAPL-contaminated samples during soil remediation

4.2.1 Experimental setup

As illustrated in Fig. 1, the experimental layout consisted of the following: (i) a Tektronix (model 1502C) cable tester, (ii) a three-rod probe, 14.5 cm long, with a wire diameter of 0.003 m and a wire spacing of 0.02 m, introduced vertically into the soil samples, (iii) a testing cell, 0.15 m high and 0.08 m in diameter, and (iv) a peristaltic pump used for upward movement of the washing solution.

4.2.2 Sample preparation and testing procedures

Soil was oven dried at 105 C and passed through a 2 mm sieve. Known amounts of soil and oil were mixed together, shaken, and then kept for 24 h in sealed plastic bags to avoid any evaporation and ensure a uniform distribution of oil within the sample and good oil adsorption by the soil matrix. The samples were then allocated to cylindrical boxes. With a view to achieving different degrees of (initial) soil contamination, volumetric NAPL content (θNAPL) was varied from 0.05 to 0.40 (in steps of 0.05). In all, each washing solution comprised eight oil-contaminated soil samples.

For all experiments, the soil samples were placed in the vessels in various steps at a bulk density of 1.13 g cm−3. During TDR measurements, the soil samples were conserved at a temperature of 25 C by using a thermostat box. Remediation was performed using an upward flux of diverse pore volumes T of three washing solutions (wd, wda no. 1 and wda no. 2) supplied at the rate of 90 cm3 h−1, corresponding to a Darcian velocity of 1.8 cm h−1. After collection of the outflow from the soil columns, the surnatant NAPL was separated from the washing solution and the quantity of NAPL remediated from the soil was determined.

The obtained data series were employed to calibrate the proposed dielectric model of Eq. (10). An independent dataset, obtained in the same manner as the calibration dataset, was used for model validation.

4.3 Numerical indices for model performance evaluation

The goodness of Eq. (10) was evaluated using two different criteria: (i) the mean bias error (MBE) and (ii) the model efficiency (EF), computed according to the following relations (Legates and McCabe Jr., 1999):

(11)MBE=i=1NEi-OiN,(12)EF=1-i=1NEi-Oi2i=1NOi-O2,

where Ei and Oi are respectively the expected and the observed value, O is the mean of the observed data, and N is the number of observations.

https://www.hydrol-earth-syst-sci.net/23/3593/2019/hess-23-3593-2019-f02

Figure 2Selection of experimental relationships between the measured dielectric permittivity (εs-ws-NAPL) and number of pore volumes T under the effect of different washing solutions: (i) water–detergent (wd) and (ii) water–detergent–alcohol (wda no. 1 and wda no. 2).

Download

MBE measures the differences between model-simulated data and measured values (positive MBE values are used to indicate average overprediction, while negative values indicate underprediction). The model's ability to forecast θNAPL is described by parameter EF, according to which EF = 1 indicates perfect accord between predicted and measured data.

https://www.hydrol-earth-syst-sci.net/23/3593/2019/hess-23-3593-2019-f03

Figure 3Volume of NAPL recovered (VNAPL-Rem) with respect to the initial volume of NAPL present in the soil sample (V0) of different washing solutions (wd, wda no. 1 and wda no. 2) for different experiments (θNAPL=0.15, 0.20, 0.25, 0.30, 0.35 and 0.40).

Download

5 Results and discussion

5.1 Influence of washing solution on NAPL removal

Figure 2a–f, with reference to the most representative experimental results, reveal the influence of pore volumes T on evaluated bulk dielectric permittivity (εs-ws-NAPL) for the soil specimens initially polluted with oil. As the washing solution started to remove oil, the dielectric permittivity rose due to the larger dielectric permittivity of the flushing mixture. As the remediation solution continued to move upward, the rising rate of the dielectric permittivity decreased and asymptotically approached a constant value. This steady value was smaller than that observed when the soil specimens were completely saturated by only the flushing solution (i.e., wd, wda no. 1 or wda no. 2), which in our tests corresponds to the condition of a completely decontaminated soil. This difference in values is undoubtedly due to oil confined in soil pores (i.e., NAPL residual saturation). For the same reason, residual saturation may explain why insignificant oil remediation was observed for θNAPL values less than 0.15. This aspect may be explained by the fact that for low volumetric NAPL contents, the non-wetting fluid (oil) is disconnectedly distributed (i.e., immobile) in the soil samples, which means that θNAPL is close to the limiting “residual value”, and thus NAPL loses its ability to move in the soil in response to a hydraulic gradient (i.e., capillary retention forces are greater than gravitational forces, which tend to immobilize the NAPL; Brost and DeVaull, 2000).

The NAPL volumes removed for different washing solutions and the initial volumetric content of NAPL are compared in Fig. 3. For all the three cleaning solutions adopted, the experiments ultimately demonstrate (for a fixed θNAPL) the same results in terms of soil decontamination, and they show that NAPL removal increases with increasing θNAPL. In some cases (i.e., θNAPL=0.15, 0.20 and 0.30), contaminated samples flushed with the wda no. 1 solution yield slightly higher removal efficiency values compared to the samples flushed with wd and wda no. 2. Martel et al. (1998) suggest the need to investigate the best water–surfactant–alcohol combination in order to enhance NAPL solubilization in soil.

5.2 Model calibration and validation

For the model (Eq. 10) calibration methodology, with reference to the three washing solutions (wd, wda no. 1 and wda no. 2), we analyze the effect of the measured dielectric permittivity on volumetric NAPL content (θNAPL) in order to estimate the α parameter of the model. The complete calibration dataset of estimated α parameters is reported in Table 1. The α parameter of the mixing model was determined, for a fixed θNAPL value and washing solution, by an optimization procedure based on the least-squares technique and was kept constant for each of the remediation tests developed.

Table 1Estimated α parameter of Eq. (10) for all three washing solutions (wd, wda no. 1 and wda no. 2) and the volumetric NAPL content (θNAPL) tested.

Download Print Version | Download XLSX

A permittivity value of 3.70 was adopted for the solid phase. This value was determined using the “immersion method”, which is commonly employed for estimating the εs of soils (Robinson and Friedman, 2003; Kameyama and Miyamoto, 2008; Comegna et al., 2013b).

For the sake of brevity, a selection of the experimental εs-ws-NAPLθNAPL relationships (validation dataset) is reported in Fig. 4a–f. The data in Fig. 4 (except for Fig. 4e and f) show that some of the model-simulated values tend to overestimate the measured data. This behavior is mostly restricted to the beginning of the remediation process, when a rapid change in dielectric permittivity may be observed. This behavior was also verified in other tests (not shown here) and may be explained by invoking both NAPL properties such as liquid density; surface tension and viscosity; and soil properties including moisture content, relative permeability and soil porosity (Brost and DeVaull, 2000; Wang et al., 2013).

https://www.hydrol-earth-syst-sci.net/23/3593/2019/hess-23-3593-2019-f04

Figure 4(a–f) Selection of observed (symbols) and modeled (dashed lines) volumetric NAPL content (θNAPL) versus dielectric permittivity (εs-ws-NAPL), with reference to the three washing solutions (wd, wda no. 1 and wda no. 2) used during the remediation tests.

Download

Mercer and Cohen (1990) referred to the existence, in NAPL-contaminated soils, of a “double fluid domain”, defined as the composition of the following: (i) mobile pools, which are NAPL-connected phases that move in the soil, and (ii) immobile residuals (i.e., low-permeability regions), which depend on small disconnected blobs or ganglia within the contaminated soil (see also Sect. 5.1 above). As long as the flushing continues, mobile pools are reduced and the oil tends increasingly to be trapped in the immobile areas. This means that, during soil cleaning, the capacity of non-wetting fluids to respond to gravitational forces gradually diminishes (Luckner et al., 1989). From a dielectric point of view, this mechanism may appear as a rapid dielectric permittivity increase (identified in Fig. 4 as a “fast oil mobility region”) within a few pore volumes. When this fast mobility mechanism is dominant, the predictions of Eq. (10) fail.

Another possible explanation for this discrepancy between the observed and the predicted permittivity values may be linked to the propensity of NAPL-water mixtures to form macroinclusions in the soil (Persson and Berndtsson, 2002), which affected the initial pore-scale distribution of NAPL, and thus the global dielectric response of the medium (Ferré et al., 1996), during the first remediation stages.

However, since the phenomenon is mostly limited to the initial part of the washing process, overall model effectiveness is not compromised, as also shown in Table 2, which summarizes the goodness-of-fit statistical indices, and in Fig. 5a–f, where the estimated θNAPL from Eq. (10) and the known θNAPL are illustrated in a series of 1:1 scatter plots.

https://www.hydrol-earth-syst-sci.net/23/3593/2019/hess-23-3593-2019-f05

Figure 5(a–f) Measured (Eq. 10) vs. known volumetric NAPL content (θNAPL) of contaminated soils, with reference to the different remediation tests in Fig. 4.

Download

Table 2Model efficiency (EF) and mean bias error (MBE) statistical indices, referring to measured and predicted (Eq. 10) volumetric NAPL content (θNAPL), calculated in the range of model applicability (0.15θNAPL0.40).

Download Print Version | Download XLSX

Overall, both graphical and quantitative evaluations in terms of MBE and EF reveal the suitability of the dielectric model adopted to estimate the volumetric NAPL content in the θNAPL range 0.15–0.40.

6 Conclusions

This paper presented an extensive dataset of remediation experiments that were conducted on a laboratory scale using corn oil as a soil contaminant and three different solutions for soil cleaning. The results of these tests were employed to investigate the potential of the TDR technique in monitoring the development of a steady-state decontamination process.

Dielectric data analysis showed that, during soil flushing, dielectric permittivity behavior is highly dependent on the initial volumetric content and intrinsic permittivity of the specific NAPL: “removal of NAPL produces an increase in bulk dielectric permittivity” due to the low value of oil permittivity. The experiments conducted also allowed us to calibrate and validate a dielectric mixing model (Eq. 10). The model outcomes are encouraging; the calculated statistical indices confirmed a high accuracy in NAPL predictions of the α model at different stages during soil cleaning, with the only exception of the initial cleaning stage (confined to the low values of T), where the eventual presence of a “fast flow region” may limit its applicability.

The approach requires additional experiments and datasets for model calibration and validation in different pedological contexts, mainly to confirm the potential of the methodology developed. Furthermore, an effort should be made, introducing the water phase, ab initio in the experimental setup, to simulate a possible natural contamination–decontamination scenario more accurately. Finally, full field-scale tests should also be conducted to evaluate the performance of Eq. (10) in real field conditions.

Data availability

The dataset used in this paper is available on request to alessandro.comegna@unibas.it.

Author contributions

The authors jointly collaborated on the development of the present research, which is based on ACom's idea.

Competing interests

The authors declare that they have no conflict of interest.

Review statement

This paper was edited by Marnik Vanclooster and reviewed by Ty P. A. Ferré, Magnus Persson, and one anonymous referee.

References

Allison, L. E.: Organic carbon, in: Methods of Soil Analysis, Part 1, Agron. Monograph, vol. 9, edited by: Klute, A., ASA and SSSA, Madison, 1367–1378, 1965. 

Birchack, J. R., Gardner, C. Z. G., Hipp, J. E., and Victor, J. M.: High dielectric constant microwave probes for sensing soil moisture, Proc. IEEEE, 62, 93–98, 1974. 

Brost, E. J. and DeVaull, G. E.: Non-Aqueous phase liquid (NAPL) mobility limits in soils, Soil Groundw. Res. Bull., 9, 1–9, 2000. 

Comegna, A., Coppola, A., Dragonetti, G., and Sommella, A.: Dielectric response of a variable saturated soil contaminated by Non-Aqueous Phase Liquids (NAPLs), Proced. Environ. Sci., 19, 701–710, 2013a. 

Comegna, A., Coppola, A., Dragonetti, G., Severino, G., Sommella, A., and Basile, A.: Dielectric properties of a tilled sandy volcanic-vesuvian soil with moderate andic features, Soil Till. Res., 133, 93–100, 2013b. 

Comegna, A., Coppola, A., Dragonetti, G., Chaali, N., and Sommella, A.: Time domain reflectometry-measuring dielectric permittivity to detect soil non-aqueous phase liquids contamination-decontamination processes, J. Agricult. Eng., XLIV, e167, https://doi.org/10.4081/jae.2013.409, 2013c. 

Comegna, A., Coppola, A., Dragonetti, G., and Sommella, A.: Estimating non-aqueous phase liquid (NAPL) content in variable saturated soils using time domain reflectometry (TDR), Vadose Zone J., 15, 13, https://doi.org/10.2136/vzj2015.11.0145, 2016. 

Comegna, A., Coppola, A., Dragonetti, G., and Sommella, A.: Interpreting TDR signal propagation through soils with distinct layers of nonaqueous-phase liquid and water content, Vadose Zone J., 16, 5, https://doi.org/10.2136/vzj2017.07.0141, 2017. 

Coppola, A., Dragonetti, G., Comegna, A., Lamaddalena, N., Caushi, B., Haikal, M. A., and Basile, A.: Measuring and modeling water content in stony soils, Soil Till. Res., 128, 9–22, 2013. 

Coppola, A., Comegna, A., Dragonetti, G., Gerke, H. H., and Basile, A.: Simulated water flow and solute transport in shrinking soils, Vadose Zone J., 14, 9, https://doi.org/10.2136/vzj2015.02.0021, 2015. 

Day, P. R.: Particle fractionation and particle-size analysis, in: Methods of Soil Analysis, Part 1, edited by: Black, C. A., American Society of Agronomy, Madison, 545–567, 1965. 

Eckert, D. J.: Soil pH, in: Recommended chemical soil test procedures for the North Central Region, edited by: Dahnke, W. C., North Bulletin No. 221, Dakota Agricultural Experiment Station, Fargo, 6–8, 1988. 

Endres, A. and Redman, J. D.: Modeling the electrical properties of porous rocks and soils containing immiscible contaminants, edited by: Bell, R. S. and Lepper, C. M., in: Proceedings of the Symposium on the application of geophysics to Engineering and Environmental Problems, San Diego, 21–38, 1993. 

Ferré, P. A. and Topp, G. C.: Time domain reflectometry, in: Methods of Soil Analysis: Part 4, Physical Methods, edited by: Dane, J. H. and Topp, G. C., SSSA, Madison, WI, 434–446, 2002. 

Ferré, P. A., Rudolph, D. L., and Kachanoski, R. G.: Spatial averaging of water content by time domain reflectometry: Implications for twin rod probes with and without dielectric coatings, Water Resour. Res., 32, 271–279, 1996. 

Fetter, C. W.: Contaminant hydrogeology, in: Practice, 2nd Edn., Hall Englewood Cliffs, NJ, 247–315, 1993. 

Fitts, C. R.: Contamination sources, in: Groundwater Science, Academic Press, London, 339–343, 2002. 

Francisca, M. and Montoro, M. A.: Measuring the dielectric properties of soil-organic mixtures using coaxial impedance dielectric reflectometry, J. Appl. Geophys., 80, 101–109, 2012. 

Freeze, R. A.: The unpleasant truths about waste management, in: The Environmental Pendulum, University of California Press, Berkeley, 147–196, 2000. 

Heimovaara, T. J.: Frequency domain analysis of time domain reflectometry waveforms, 2, A four-component complex dielectric mixing model for soil, Water Resour. Res., 30, 201–209, 1994. 

Hilhorst, M. A.: Dielectric characterisation of soil, PhD dissertation, Wageningen Agricultural University, Wageningen, the Netherlands, 1998. 

IUSS Working Group WRB: World reference base for soil resources 2006: A framework for international classification, correlation and communication, 2nd Edn., World Soil Resour. Rep. 103, FAO, Rome, 2006. 

Kameyama, K. and Miyamoto, T.: Measurement of solid phase permittivity for soils by time domain reflectometry, Eur. J. Soil Sci., 59, 1253–1259, 2008. 

Knight, R.: Ground penetrating radar for environmental applications, Annu. Rev. Earth Planet. Sci., 29, 229–255, 2001. 

Knight, R. and Endres, A.: A new concept in modeling the dielectric response of sandstones: Defining a wetted rock and bulk water systems, Geophysics, 55, 586–594, 1990. 

Legates, D. R. and McCabe Jr., G. J.: Evaluating the use of “goodness-of-fit” measures in hydrologic and hydroclimatic model validation, Water Resour. Res., 35, 233–241, 1999. 

Luckner, L., van Genuchten, M. T., and Nielsen, D. R.: A consistent set of parametric models for the two-phase flow of immiscible fluids in the subsurface, Water Resour. Res., 25, 2187–2193, 1989. 

Martel, R., Gelinas, P. J., and Saumure, L.: Aquifer washing by micellar solutions: 3 Field test at the Thounin Sand Pit (L'Assomption Quebec, Canada), J. Contam. Hydrol., 30, 33–48, 1998. 

Mercer, J. W. and Cohen, R. M.: A review of immiscible fluids in the subsurface: Properties, models, characterization, and remediation, J. Contam. Hydrol., 6, 107–163, 1990. 

Miller, J. J. and Curtis, D.: Electrical conductivity and soluble ions, in: Soil Sampling and Methods of Analysis, edited by: Carter, M. R. and Gregorich, E. G., Canadian Society of Soil Science, Broken Sound Pkwy, NW, 2006. 

Mohamed, A.M.O., and Said R.A.: Detection of organic pollutants in sandy soils via TDR and eigendecomposition. J. Contain. Hydrol., 76, 235–249, 2005. 

Moroizumi, T. and Sasaki, Y.: Estimating the nonaqueous-phase liquid content in saturated sandy soil using amplitude domain reflectometry, Soil Sci. Soc. Am. J., 72, 1520–1526, 2006. 

Parnian, M. M. and Ayatollahi, S.: Surfactant remediation of LNAPL contaminated soil; effects of adding alkaline and foam producing substances, Iran. J. Chem. Eng., 2, 34–44, 2008.  

Pennell, K. D., Jin, M., Abriola, L. M., and Pope, G. A.: Surfactant enhanced remediation of soil columns contaminated by residual tetrachloroethylene, J. Contam. Hydrol., 16, 35–53, 1994. 

Persson, M. and Berndtsson, R.: Measuring nonaqueous phase liquid saturation in soil using time domain reflectometry, Water Resour. Res., 38, 1064, https://doi.org/10.1029/2001WR000523, 2002. 

Redman, J. D., Kueper, B. H., and Annan, A. P.: Dielectric stratigraphy of a DNAPL spill and implications for detection with ground penetrating radar: Aquifer restoration, ground water monitoring and geophysical methods, in: 5th national outdoor action conference, 13–16 May 1991, Las Vegas, Nevada, 1017–1030, 1991. 

Redman, J. D. and DeRyck, S. M.: Monitoring Non-Aqueous Phase Liquids in the Subsurface with Multilevel Time Domain Reflectometry Probes, in: Proceedings of the Symposium on Time Domain Reflectometry in Environmental, Infrastructure, and Mining Applications, 7–9 September 1994, Special Publication SP 19-94, NTIS PB95-105789, US Bureau of Mines, Evanston, Illinois, 207–215, 1994. 

Rinaldi, V. A. and Francisca, F. M.: Removal of immiscible contaminants from sandy soils monitored by means of dielectric measurements, J. Environ. Eng., 132, 931–939, 2006. 

Robinson, D. A. and Friedman, S. P.: The effective permittivity of dense packing of glass beads, quartz sand and their mixtures immersed in different dielectric backgrounds, J. Non-Crystal. Solids, 305, 261–267, 2003. 

Robinson, D. A., Jones, S. B., Wraith, J. M., and Or, D.: A review of advances in dielectric and electric conductivity measurements using time domain reflectometry, Vadose Zone J., 2, 444–475, 2003. 

Roth, K., Schulin, R., Fluhler, H., and Attinger, W.: Calibration of time domain reflectometry for water content measurements using a composite dielectric approach, Water Resour. Res., 26, 2267–2273, 1990. 

Topp, C. G., Davis, J. L., and Annan, A. P.: Electromagnetic determination of soil water content: Measurements in coaxial transmission lines, Water Resour. Res., 16, 574–582, 1980. 

Truong Hong, T. and Bettahar, M.: Effect of the water-oil ratio on brine/surfactant/alcohol/oil systems optimized for soil remediation, J. Mater Cy. Waste Manage., 2, 109–117, 2000. 

van Dam, R. L., Borchers, B., and Hendrickx, J. M. H.: Methods for prediction of soil dielectric properties: a review, in: Proceedings of SPIE-the International Society for Optical Engineering, 28 March–1 April 2005, Orlando, Florida, 2005. 

Wang, X. P., Quan, G. J., Pan, Y. X., Hu, R., Zhang, Y. F, Tedeschi, A., Basile, A., Comegna, A., Coppola, A., and de Mascellis, R.: Comparison of hydraulic behaviour of unvegetated and vegetation-stabilized sand dunes in arid desert ecosystems, Ecohydrology, 62, 264–274, 2013. 

Download
Short summary
We carried out a series of laboratory-controlled experiments in order to simulate different scenarios of practical interest aiming to analyze, from a dielectric point of view, the influence of different washing solutions on non-aqueous phase liquid (NAPL) removal. Furthermore, on the basis of the results obtained, we validated a dielectric mixing model for predicting the volumetric amounts of NAPL (θNAPL) within the contaminated soil as the decontamination process progressed.